(2) © All rights reserved. No part of this publication, either in English or in Hindi, may be reproduced in any form or by any means, electronic or mechanical including photocopy, recording or any information storage and retrieval system, without permission, in writing, from the Director General, CPWD, New Delhi. DISCLAIMER The rates taken in Delhi Schedule of Rates 2016 are indicative and actual rates shall be governed by the market forces. Further its use by Govt. Departments, PSUs, private bodies & individuals shall be at their own risk and discretion. CPWD shall not be responsible for any ambiguity, discrepancy, dispute or financial loss, arising directly or indirectly by using or following items of DSR by such Govt./Private bodies or individuals. For feed back and suggestions, please contact SE(TAS), CPWD, Room No. 418, ''A'' Wing, Nirman Bhawan, New Delhi. Tel. No. 011-23062339, Email: [emailprotected]. A GOVERNMENT OF INDIA PUBLICATION Published by DIRECTOR GENERAL CPWD, Nirman Bhawan, New Delhi - 110011 & Printed & Marketed by Distributed by JBA DISTRIBUTORS 4782/23, Ansari Road, Daryaganj New Delhi-110002 Phone : 4433 2211, 44332222 E-mail : [emailprotected] Website : www.jba.in. JAIN BOOK AGENCY Authorised Dealers of Govt. Publications C-9, Connaught Place, New Delhi-110001 Phones : 44556677, 23416390 upto 94 E-mail : [emailprotected] Website : www.jainbookagency.com. JAIN BOOK AGENCY (SOUTHEND) 1, Aurobindo Place Market, Hauz Khas, New Delhi-110016 Phone : 41755666 E-mail : [emailprotected] Website : www.jainbookagency.com. JAIN BOOK AGENCY (GURGAON) 19, Central Plaza Mall, Sector 53, Golf Course Road, Gurgaon 122002 Haryana Phone : 4143020 Mobile : 9810666810. JAIN BOOK AGENCY (INTERNATIONAL) RA- 11, Sector- 126, Opp. Gate No. 2A of Amity University, Noida Mobile. : 9210080580. JAIN BOOK AGENCY (GREATER NOIDA) 11 Jagat farm Complex Gama Sector Market Near OBC Bank Greater Noida Phone : 0120-4206655 JAIN BOOK DEPOT C - 4, Opp. PVR Plaza, Post Box. No. 51, Connaught Place, New Delhi-110001 (India) Phone : 011- 23416101 / 02 / 03 E-mail : [emailprotected]. (. DIAL-A-BOOK 011-44332211. Books will be delivered next day by COURIER (Payment to courier-boy) in Delhi, Noida, Ghaziabad, Faridabad & Gurgaon (nominal courier charges extra). ISBN : 978-81-932679-0-5 Also available at All Leading Booksellers & Authorised Govt. Dealers In India Price : Rs. 1200/- (for both volumes) excluding postage and forwarding charges etc..
(3) Hkkjr ljdkj Government of India. DIVAKAR GARG Director General. FOREWORD. dsUnzh; yksd fuekZ.k foHkkx fuekZ.k Hkou] ubZ fnYyh 110011 Central Public Works Department Nirman Bhawan, New Delhi- 110011 Tel : 23062556 / 1317, Fax : 23061884 E-Mail : [emailprotected]. Delhi Schedule of Rates, being published by Central Public Works Department from time to time, is a very comprehensive technical document and useful in execution of civil construction works. Apart from C.P.W.D., this Schedule of Rates is used as a guide by many departments, institutions, public sector undertakings, architects, builders, contractors, etc. The Central Public Works Department Schedule of Rates was first published in the year 1931, followed by a number of revisions/publications from time to time in order to bring it in line with the prevailing technologies and market rates. The Delhi Schedule of Rates were revised many times in the subsequent years viz 1977, 1981, 1985, 1989, 1993, 1997, 2002, 2007, 2010 (Reprint), 2012, 2013 & 2014. Earlier Hindi version of DSR was being published separately, but considering the convenience and mandate for use of Hindi, the present DSR has been made bilingual and covered in two volumes. The prices of labour and materials have registered some changes since last publication. Besides the cost, there has been spurt of new construction technologies and materials. This has necessitated revision of existing DSR 2014 to include the above changes. Although this DSR contains most of the items of DSR 2014, the nomenclature of existing items has been reviewed & updated wherever found necessary. The items pertaining to new technology and materials have been added in New Sub head 26 for use of field units and feedback on these items. I wish to place on record the technical input and effective coordination on the part of Shri Abhai Sinha, Spl. DG (HQ), Shri Balraj Chadha ADG (TD), Shri M.K. Sharma CE (CSQ)-(Civil) and the efforts put in by Shri S.P. Chaudhary Director (Tech. & PR), Shri P.P. Singh SE (TAS) and his team of officers in CSQ unit in finalizing the DSR-2016 in a short time. I am sure that this Schedule of Rates 2016 will be quite useful to all concerned Engineers & Architects in the Building construction industry in general and CPWD in particular.. Place: New Delhi Date: July 2016. (Divakar Garg) Director General.
(4) PREFACE. 1.. Delhi Schedule of Rates-2016 includes the existing items of DSR 2014 with deletion of few obsolete items, merger of similar items and addition of new items in line with emerging trends in construction Industry.. 2.. DSR-2016 is based on the prevailing market rates of materials in Delhi as on 01.04.2016. The labour rates adopted are as per minimum wages applicable w.e.f 01/04/2016 issued by Govt. of Delhi/ Govt. of India, whichever is higher.. 3.. The cost index for DSR 2016 is 102 with reference to CPWD Plinth Area Rates 2012, having base 100 as on 01/10/2012.. 4.. This DSR 2016 shall be read along with CPWD specifications 2009 Vol.-I & II with up to date Correction Slips.. 5.. Following are the Salient Features of DSR-2016.. 5.1. DSR-2016 is bilingual and in two volumes.. 6.0. 5.1.1. Sub-head Nos. 24, 25 & 26 of DSR-2014 have been re-numbered as 23, 24 & 25 respectively due to separate publication of DSR for ‘Horticulture and Land Scaping’.. 5.1.2. New Sub- head No. 26 for New Technologies and Materials has been introduced.. 5.1.3. The rates of basic materials incorporated in this DSR 2016 are considered for the materials available in the market, conforming to BIS Standards/ CPWD Specifications.. 5.1.4. The items relating to uPVC windows have been made composite & units of measurement converted from metre to square metre with a number of possible combinations of window profiles. Provision for tolerance to profiles sizes have been made to allow for innovations and vendor variations.. Keeping in view amendments in IS: 383-2016, the use of manufactured aggregate (RCA & RA) have been permitted in the Concrete and RCC work.. IV.
(5) Salient Modifications and Changes in Sub Heads: 7.1. Carriage of Materials: Item No. 1.1.18 for ‘Disposal of moorum/ building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport’ has been added.. 7.2. Concrete Work: The items with FINE SAND have been deleted.. 7.3. RCC Work: The items of 1:2:4 nominal concrete mix (M15) have been modified to 1:1 ½ :3 nominal concrete mix (M20) due to changes in IS 456 in the minimum grade of concrete to M20 keeping in view durability consideration. However, the use of nominal mix in RCC work is to be discouraged. The item no. 5.29 for Non- asbestos cement bonded wood particle board 6 mm thick as per IS: 14276 for covering of expansion joints has been added.. 7.4. Brick Work: The item No. 6.47 for ‘Autoclaved Aerated Cement blocks masonry with polymer modified adhesive mortar’ has been added.. 7.5. Stone Work: Item No. 7.23.5 wall lining (veneer work) with Gang saw cut sand stone has been added.. 7.6. Marble Work: Item No. 8.13 for Polished Granite stone flooring has been added.. 7.7. Wood Work: Item No. 8.13 for Cement bonded wood particle board as per IS:14276 has been added. Item Nos. 9.147.A to 9.147.F.4 for uPVC shutters having mode of measurement in square metre have been added by replacing old item in running metre. Item Nos. 9.161 to 9.165 (for 120 minutes fire rated) fire resistant door have been added.. 7.8. Steel Work: Item Nos. 10.31 for angle iron frames for doors, windows for Maintenance Works has been added.. 7.9. Flooring: Items Nos. 11.37.A & 11.46. A for ceramic tiles for skirting and screen printed border tile have been added.. 7.10. Roofing: Item No. 12.26.2 for 6 mm thick Cement bonded wood particle board as per IS:14276 has been added.. 7.11. Finishing: Item No. 13.86 for 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar has been added.. 7.12. Repairs to building: Item No. 14.75 for repair to plaster with white cement based polymer modified self curing mortar has been added.. V.
(6) 7.13. Road Work: Item No. 16.95 to 16.97 for Gabion structure with Mechanically Woven Double Twisted Hexagonal Shaped Wire mesh Gabion Boxes have been added.. 7.14. Sanitary Installation: Items pertaining to Hubless pipes as per IS:15905 ( 22 Nos.) vide Item Nos 17.35.1.3 to 17.60.2.3 have been added. Item No 17.81 pertaining to floor mounted double siphoned water closet have been added.. 7.15. Water Proofing : Item No. 22.22 to 22.26 for waterproofing treatment have been added.. 8.0. New Technologies and Materials With a view to give boost to make in India initiative of the Government, a new sub Head has been added for New Technologies and Materials. These new items are included for a period of two years and then performance shall be reviewed. Following are items added under this sub head.. 8.1. Phenol bonded Bamboo wood flooring, wall skirting, wall cladding. 25 mm and 30mm thick panelled and panelled /glazed shutters for doors and windows and Bamboo wood frame.. 8.2. 50mm thick extruded polystyrene rigid insulation board for cavity wall and under deck insulation.. 8.3. Relevant items for modular kitchen.. 8.4. Items relating to Polypropylene Geogrid, Nonwoven Geotextile drainage composite and High strength flexible Geogrids (HSFG) as soil reinforcement.. 8.5. Items for Aluminium profile industrial troughed sheet roofing.. 8.6. Security guard with and without gun.. 8.7. P/F Densified calcium silicate false ceiling tiles, GRG false ceiling tiles and Mineral fiber false ceiling tiles.. 8.8. Repair and Rehabilitation 13 Nos. Items. 8.9. New Technology items viz. Light Gauge Steel Framed Structure (LGSFS), Expanded Polystyrene Core (EPS Core) wall panel and roof/floor panels and Customized Aluminum formwork for monolithic construction.. 8.10. While preparing the DSR, it is ensured that brand name, product of any particular company, proprietary items does not find place in the nomenclature of the items. In case, any such item having brand name/ manufactures name is noticed, it may be brought to the notice of Superintending Engineer (TAS), CPWD, Nirman Bhawan, New Delhi for remedial action.. 9.0. Lot of efforts have gone into the preparation of this Delhi Schedule of Rates 2016 (Bilingual). I convey my deep appreciation and sincere thanks to Shri M. K. Sharma - CE(CSQ), Shri S. P. Chaudhary - Director(Tech. & PR), Shri P. P. Singh - SE(TAS) and his team comprising Shri R. B. Garg - EE(TAS-II), Shri K. R. Meena - EE(TAD), Shri Kunwar Chandresh - EE(eGov.), Shri S. K. Srivastava - EE(QA), Shri D. K. Chaudhary - EE(QA), VI.
(7) Shri D. S. Adhikari - AE(QA), Shri K. N. Singh - AE(TAS), Shri D. K. Malhotra - AE(TAS), Ms. Anjana Reghu - JE, Shri Chalapaka Ramraju - JE, Shri Naveen Kumar P. - JE, Shri Jai Prakash - Chief Estimator, Shri Kishan Singh - Sr. D/man, Shri Bhim Singh Sr. D/man; Shri Sanjeev Rastogi - SE(C&M) and his team comprising Shri Virendra Kumar - EE(M), Shri Keshav Ram - EE(C), Shri H. K. Gupta - AE(C), Shri Dalbir Singh - Sr.D/man; Shri Som Lal Kajal - EE(HQ); Shri Sanjay Singh - AD(OL) and his team for Hindi translation of DSR-2016, and other officers and staff of CSQ whose names are not mentioned here, for their sincere efforts made in the preparation of this document in such a short time. Various Committees and field units, who contributed field inputs, also deserve appreciation for their timely help. 10.0. Although due care has been taken to print the DSR- 2016 as correctly as possible, there is possibility that some errors might have crept in inadvertently. In case, any error or omission is noticed, it may be brought to the notice of Superintending Engineer (TAS), CPWD, Room no. 418, ‘ A’, Nirman Bhawan, New Delhi – 110011 (Tele fax. 011-23062339 ).. Suggestions for improvement are always welcome.. (Balraj Chadha) ADG (TD) CPWD. Note :- In case of any discrepancy between English and Hindi versions, the English version shall be held valid. VII.
(8) Committees for Bringing Out New edition of DSR 2016 CPWD DSR is a very comprehensive document. Delhi Schedule of Rate 2016 includes the existing item of DSR 2014 with deletion of few obsolete items, merger of similar items and addition of new items in line with emerging trends in construction industry. DSR 2016 is based on prevailing market rates of material and labour in Delhi as on 01.04.2016. To bring out new edition of DSR 2016 it was felt necessary to take input from as many officers as possible and utilize their experiences in this regard. Accordingly, the following committees were constituted for the above task. 1.. Drafting Committee. (a) (b) (c) (d) (e) (f) (g) (h) (i) (j) (k). Shri M.K. Sharma, CE (CSQ)-Civil Shri S.P. Chaudhary, Director (Tech. & PR) Shri Sanjeev Rastogi, SE (C&M) Shri P.P. Singh, SE (QA-cum-TLC) Shri K.R. Meena, EE (TAD) Shri R.B. Garg, EE (TAS) Shri Kunwar Chandresh, EE (E-gov.) Shri D.K. Chaudhary, EE (QA) Shri S.K. Srivastava, EE (QA) Shri Keshav Ram, EE (Contracts) Shri Virendra Kumar, EE (Manual). 2.. Committee for review/revision of items of sub head 3, 4, 5 & 20 of DSR 2014. (a) (b) (c). Shri A.K. Garg, CE (CDO) Shri Rajesh Khare, SE (D) Shri A.K. Gupta, SE (D). 3.. Committee for review/ revision of items of sub head 9, 21, & 25 of DSR 2014. (a) (b) (c). Shri Prabhakar Singh, CE (NDZ)-I Shri K.S. Warriach, SE (P)-NDZ-I Shri Manoj Talreja, SE DCC-II. 4.. Committee for review/ revision of items of sub head 1, 2 & 26 of DSR 2014. (a) (b) (c). Shri Akhilesh Kumar, CE (NDZ)-II Shri R.K. Kashyap SE (P)-NDZ-II Shri B.K. Sinha, SE-DCC-IX. Chairman Member Member Member Member Member Member Member Member Member Member. Chairman Member Member. Chairman Member Member. Chairman Member Member. VIII.
(9) 5.. Committee for review/ revision of items of sub head 11,12 & 13 of DSR 2014. (a) (b) (c). Shri Bhagwan Singh, CE (NDZ)-III Shri N.K. Khatri, SE (P)-DCC-VI Shri Rajeev Gupta, SE-DCC-VIII. 6. (e) (a) (b). Committee for review/revision of items of sub head 6, 7, 10, & 24 of DSR 2014 Shri P.K. Singh, CE (NDZ)-IV Chairman Shri Rajeev Gupta, SE-DCC-V Member Shri R.R. Verma, PM SCP Member. 7. (a) (b) (c) (d). Committee for review / revision of items of sub head 17 & 18 of DSR 2014 Shri Ranjit Singh, CE (NDZ-V) Chairman Shri Rajesh Banga, SE-DCC-IV Member Shri Prem Mohan, PM NDP Circle Member Shri Anurag Khare, SE-VBC Member. 8. (a) (b). Committee for review/revision of items of sub head 22 of DSR 2014 Shri S.L. Meena, CE (NDZ)-VI Chairman Shri O.S. Saini, SE-DCC-X Member. 9.. Committee for review/revision of items of sub head 14 & 15 of DSR 2014. (a) (b) (c). Shri Brijendra Kumar, CE (NDZ)-VII Shri S.S. Khanna, SE-DCC-XI Shri Gajendra Kumar, SE-DCC-XII. 10. (a) (b). Committee for review/revision of items of sub head 8 of DSR 2014 Shri Rabindra Kumar, CE (NDZ-)VIII Chairman Shri Anurag Garg, SE GCC Member. 11. (a) (b) (c) (d). Committee for review/revision of items of sub head 16 & 19 of DSR 2014 Shri S.K. Rampal, CE (PWD-MZ-I) Chairman Shri Pradeep Gupta, CE, (East Zone) Member Shri A.K. Agarwal, SE (NE) Member Shri K.R. Bhandaria, SE (NW) Member. 12.. Committee for making available basic rates for building materials as on 01.04.2016. (a) (b) (c) (d) (e). Shri Prabhakar Singh, CE (NDZ)-I Now ADG (NDR) Shri Akhilesh Kumar, CE (NDZ)-II Shri Bhagwan Singh, CE (NDZ)-III Shri P.K. Singh, CE (NDZ)-IV Shri S.K. Rampal, CE (PWD MZ-I). Chairman Member Member. Chairman Member Member. The above committees carried out their work under the overall supervision and guidance of Shri P.K. Garg the then ADG (TD). **** IX.
(10) C O N T E N T S. Vol. 1 SH. No.. NAME OF SUB-HEAD. PAGE No.. A.. BASIC RATES. 0.1. HIRE CHARGES OF PLANTS. 2. 0.2. LABOUR. 5. 0.3. MATERIALS. 7. 0.4. CARRIAGE CODES. B.. SUB -HEADS. 1.. Carriage of Materials. 66. 2.. Earth Work. 74. 3.. Mortars. 82. 4.. Concrete Work. 85. 5.. Reinforced Cement Concrete. 93. 6.. Brick Work. 108. 7.. Stone Work. 116. 8.. Marble and Granite Work. 126. 9.. Wood and PVC Work. 131. 10.. Steel Work. 179. 11.. Flooring. 187. 12.. Roofing. 201. 63. X.
(11) C O N T E N T S. Vol. 2 SH. No.. NAME OF SUB-HEAD. PAGE No.. 13. Finishing. 223. 14. Repairs to Buildings. 236. 15. Dismantling and Demolishing. 251. 16. Road Work. 259. 17. Sanitary Installations. 283. 18. Water Supply. 308. 19. Drainage. 349. 20. Pile work. 364. 21. Aluminium Work. 371. 22. Water Proofing. 378. 23. Rain Water Harvesting & Tubewells. 389. 24. Conservation of Heritage Buildings.. 395. 25. Structural Glazing Aluminium Composite Panel. 399. 26. New Technologies and Materials. 407. C.. CEMENT CONSUMPTION STATEMENT. 429. D.. BITUMEN CONSUMPTION STATEMENT. 464. Note: For Sub Heads 1 to 12 refer to Vol. 1. XI.
(12) DELHI SCHEDULE OF RATES (Vol. 2). fnYyh nj vuqlwph ¼Hkkx - 2½. 2016.
(13) SUB HEAD : 13.0. FINISHING. 223.
(14) BASIC RATES (SH: 13.0 FINISHING) Code No.. Description. Unit. Rate. 0101. Bhisti. day. 407.00. 0112. Carpenter 2nd class. day. 448.00. 0114. Beldar. day. 368.00. 0115. Coolie. day. 368.00. 0117. Assistant Fitter or 2nd class Fitter. day. 448.00. 0122. Mason (for plaster of paris work) 1st class. day. 487.00. 0123. Mason (brick layer) 1st class. day. 487.00. 0131. Painter. day. 448.00. 0141. White Washer. day. 407.00. 0155. Mason (average). day. 467.00. 0156. Carpenter (Average). day. 467.00. 0324. Coal Tar. litre. 30.00. 0367. Portland Cement (OPC-43 grade). tonne. 5700.00. 0368. White Cement. tonne. 11200.00. 0763. Glue. 0771 0772. kilogram. 70.00. Kerosene oil. litre. 45.00. White Cement based Polymer modified self curing compound in powder form. kg. 15.00. 0775. Dehradun white lime. quintal. 550.00. 0776. Satna lime. quintal. 370.00. 0777. Dry hydrated lime (factory made). quintal. 280.00. 0801. Silicon and acrylic emulsion. litre. 130.00. 0802. Acrylic distemper 1st quality , having VOC content less than 50 grams/ litre. Kg. 38.00. 0803. Acrylic emulsion, having VOC content less than 50 grams/ litre. litre. 180.00. 0804. Premium acrylic emulsion of interior grade, having VOC content less than 50 grams/ litre. litre. 210.00. Synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre. litre. 200.00. Ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre. litre. 125.00. Ready mixed red oxide zinc chromatic on steel/ iron work, having VOC content less than 250 grams/ litre. litre. 120.00. Water thinnable cement primer for interior wall surface, having VOC content less than 50 grams/ litre. litre. 56.00. 0805 0806 0807 0808 0809. Exterior primer. kilogram. 52.00. 0815. Dry distemper. kilogram. 30.00. SUB HEAD : 13.0 FINISHING. 224.
(15) Code No.. Description. Unit. Rate. kilogram. 45.00. 0816. Oil bound washable distemper/ Acrylic distemper. 0818. Linseed oil (double boiled). litre. 200.00. 0820. Cement primer. litre. 60.00. 0821. Distemper primer. litre. 59.00. 0823. Pink primer (for wood). litre. 85.00. 0824. White cement based putty. kg. 20.00. 0826. Aluminium paint. litre. 130.00. 0827. Acid proof paint (chocolate or black). litre. 225.00. 0828. Anticorrosive bituminous paint (black). litre. 100.00. 0829. Black Japan paint. litre. 90.00. 0830. Enamel paint. litre. 155.00. 0831. Floor enamel paint in all shades except green. litre. 122.00. 0833. Synthetic enamel paint in black or chocolate shade. litre. 170.00. 0834. Synthetic enamel paint in all shades except black or chocolate shade. litre. 150.00. 0835. Plastic emulsion paint. litre. 200.00. 850. White lead. kilogram. 150.00. 0851. Water proofing cement paint. kilogram. 38.00. 0855. Wax polish (ready made). kilogram. 250.00. 0856. Ordinary varnish. litre. 90.00. 0857. Superior copal varnish. litre. 130.00. 0858. Superior spar varnish. litre. 130.00. 0859. Oil type wood preservative. litre. 140.00. 0868. Premixed super white gypsum plaster. kg. 5.00. 0869. Plaster of Paris. kilogram. 4.00. 0982. Coarse sand (zone III). 0999. Shellac. 1000. cum. 1200.00. kilogram. 300.00. Spirit. litre. 50.00. 1179. Crushed stone 2.36 mm to 12.5 mm size. cum. 900.00. 1198. Second class kail wood in planks. 10 cudm. 260.00. 1213. Water proofing materials. kilogram. 35.00. 1216. Whiting. quintal. 600.00. 2202. Carriage of Stone aggregate below 40 mm nominal size. cum. 103.77. 2203. Carriage of Coarse sand. cum. 103.77. 2209. Carriage of Cement. tonne. 92.24. 2911. Stone chippings/ screenings 10/ 11.2 mm nominal size. cum. 1200.00. 4201. Aluminium primer. litre. 88.00. 4202. Red oxide Zinc chromate primer. litre. 65.00. 4203. Copper acetate. kilogram. 300.00. SUB HEAD : 13.0 FINISHING. 225.
(16) Code No.. Description. Unit. Rate. 4204. Hydrochloric acid. kilogram. 35.00. 4205. Copper chloride. kilogram. 280.00. 4206. Copper nitrate. kilogram. 220.00. 4207. Ammonium chloride. kilogram. 20.00. 7239. Epoxy paint. litre. 240.00. 7240. Fire retardant paint. litre. 269.00. 7306. Aluminium T or L sections. kilogram. 200.00. 8504. Multi surface paint. litre. 255.00. 8505. Acrylic exterior paint. litre. 170.00. 8506. Premium Acrylic exterior paint. litre. 203.00. 8507. Textured exterior paint. litre. 230.00. 8509. Special Primer (C.W.). litre. 140.00. 8510. Metal Primer (U.G.). litre. 90.00. 8733. Synthetic ployster triangular fibre of length 6 mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40. kg. 400.00. 9977. Carriage. L.S.. 1.73. 9988. Carriage and sundries. L.S.. 1.73. 9999. Sundries. L.S.. 1.73. SUB HEAD : 13.0 FINISHING. 226.
(17) 13.0 FINISHING Code No.. Description. Unit. Rate. Note :- Rates for external plastic are for height upto 10m from ground level in less otherwise stated. CEMENT PLASTER (IN FINE SAND) 13.1. 13.2. 13.3. 12 mm cement plaster of mix : 13.1.1. 1:4 (1 cement: 4 fine sand). sqm. 172.95. 13.1.2. 1:6 (1 cement: 6 fine sand). sqm. 160.35. 15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.1. 1:4 (1 cement: 4 fine sand). sqm. 200.25. 13.2.2. 1:6 (1 cement: 6 fine sand). sqm. 185.20. 20 mm cement plaster of mix : 13.3.1. 1:4 (1 cement: 4 fine sand). sqm. 240.15. 13.3.2. 1:6 (1 cement: 6 fine sand). sqm. 220.60. CEMENT PLASTER (IN COARSE SAND) 13.4. 13.5. 13.6. 12 mm cement plaster of mix : 13.4.1. 1:4 (1 cement: 4 coarse sand). sqm. 180.85. 13.4.2. 1:6 (1 cement: 6 coarse sand). sqm. 168.25. 15 mm cement plaster on rough side of single or half brick wall of mix: 13.5.1. 1:4 (1 cement: 4 coarse sand). sqm. 209.65. 13.5.2. 1:6 (1 cement: 6 coarse sand). sqm. 194.60. 20 mm cement plaster of mix : 13.6.1. 1:4 (1 cement: 4 coarse sand). sqm. 252.40. 13.6.2. 1:6 (1 cement: 6 coarse sand). sqm. 232.85. CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT 13.7. 13.8. 13.9. 12 mm cement plaster finished with a floating coat of neat cement of mix : 13.7.1. 1:3 (1 cement: 3 fine sand). sqm. 226.80. 13.7.2. 1:4 (1 cement: 4 fine sand). sqm. 214.20. 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 13.8.1. 1:3 (1 cement: 3 fine sand). sqm. 256.55. 13.8.2. 1:4 (1 cement: 4 fine sand). sqm. 241.50. Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 13.9.1. 12 mm cement plaster. sqm. 234.70. 13.9.2. 20 mm cement plaster. sqm. 313.25. SUB HEAD : 13.0 FINISHING. 227.
(18) Code No.. Unit. Rate. sqm. 265.95. 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).. sqm. 255.55. 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.. sqm. 272.05. 13.13. 12 mm cement plaster 1:2 (1 cement : 2 stone dust).. sqm. 201.95. 13.14. 15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall.. sqm. 234.90. 20 mm cement plaster 1:2 (1 cement : 2 stone dust).. sqm. 285.30. sqm. 143.80. 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams.. sqm. 192.85. Neat cement punning.. sqm. 42.60. sqm. 438.90. sqm. 415.00. .Per bag of 50 kg cement used in the mix. 50.35. 13.10. Description 15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall. CEMENT PLASTER IN TWO COATS. 13.11. 13.12. 13.15. 6 MM CEMENT PLASTER 13.16. 6 mm cement plaster of mix : 13.16.1. 13.17. 13.18. 1:3 (1 cement : 3 fine sand). ROUGH CAST PLASTER 13.19. Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. 13.19.1. Ordinary cement finish using ordinary cement. PEBBLE DASH PLASTER 13.20. 13.21. Pebble dash plaster upto 10 m height above ground level with a mixture of washed pebble or crushed stone 6 mm to 12.5 mm nominal size, dashed over and including fresh plaster in two layers under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. SUB HEAD : 13.0 FINISHING. 228.
(19) Code No. 13.22 13.23. 13.24. 13.25. 13.26. Description Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.. Unit. Rate. sqm. 40.65. Extra for plastering on circular work not exceeding 6 m in radius: 13.23.1. In one coat. sqm. 20.85. 13.23.2. In two coats. sqm. 31.80. Extra for plastering done on moulding, cornices or architraves including neat finish to line and level: 13.24.1. In one coat. sqm. 305.45. 13.24.2. In two coats. sqm. 503.20. Extra for plastering: 13.25.1. Spherical ceiling. sqm. 77.70. 13.25.2. Groined ceiling. sqm. 84.45. 13.25.3. Flewing soffits. sqm. 51.20. sqm. 118.70. sqm. 48.85. Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ARTIFICIAL STONE PLASTER. 13.27. Extra for lining out plaster to imitate stone or concrete blocks walling. PLAIN CEMENT MORTAR BANDS. 13.28. 13.29. 13.30. 12 mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 fine sand): 13.28.1. Flush Band. cm per metre. 3.45. 13.28.2. Sunk Band. cm per metre. 3.75. 13.28.3. Raised Band. cm per metre. 4.25. 13.28.4. Moulded Band. cm per metre. 7.15. 18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand): 13.29.1. Flush Band. cm per metre. 4.25. 13.29.2. Sunk Band. cm per metre. 4.65. 13.29.3. Raised Band. cm per metre. 5.25. 13.29.4. Moulded Band. cm per metre. 9.60. cm per metre. 9.60. 18 mm thick moulded cement mortar band in two coats under layer 12 mm thick with cement mortar 1:5 (1 cement : 5 coarse sand) top layer 6 mm thick with cement mortar 1:4 (1 cement : 4 fine sand). POINTING ON BRICK WORK. 13.31. Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): 13.31.1. Flush / Ruled/ Struck or weathered pointing. sqm. 115.85. 13.31.2. Raised and cut pointing. sqm. 188.70. SUB HEAD : 13.0 FINISHING. 229.
(20) Code No.. Description. Unit. Rate. sqm. 158.45. POINTING ON TILE BRICK WORK 13.32. Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand): 13.32.1. Flush/ Ruled/ Struck or weathered pointing. POINTING ON STONE WORK 13.33. 13.34 13.35. Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : 13.33.1. Flush/ Ruled pointing. sqm. 168.45. 13.33.2. Raised and cut pointing. sqm. 305.70. sqm. 319.25. sqm. 95.05. sqm. 5.40. sqm. 17.25. sqm. 7.00. New work (two or more coats) with a base coat of white washing with lime. sqm. 23.60. New work (two or more coats) with a base coat of whiting. sqm. 23.25. Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.. sqm. 71.85. sqm. 93.70. sqm. 53.15. sqm. 36.95. sqm. 58.80. Raised and cut pointing on stone work in white cement mortar 1:3 (1 white cement : 3 marble dust). Pointing on stone slab ceiling with cement mortar 1:2 (1 cement : 2 fine sand): 13.35.1. 13.36. Flush/ Ruled pointing. Extra for pointing on walls on the outside at height more than 10 m from ground level for every additional height of 3 m or part there of. INTERIOR FINISHING. 13.37. White washing with lime to give an even shade : 13.37.1. New work (three or more coats). 13.38. Satna lime wash on walls with one coat.. 13.39. Colour washing such as green, blue or buff to give an even shade : 13.39.1 13.39.2. 13.40. 13.41. Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 13.41.1. 13.42. Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. 13.42.1. 13.43. New work (two or more coats) over and including water thinnable priming coat with cement primer. Two or more coats on new work. Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 13.43.1. Water thinnable cement primer. EXTERIOR FINISHING 13.44. Finishing walls with water proofing cement paint of required shade : 13.44.1. New work (Two or more coats applied @ 3.84 kg/10 sqm). SUB HEAD : 13.0 FINISHING. 230.
(21) Code No. 13.45. Description. 13.48.2. 13.48.3. 96.05. sqm. 96.80. Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm. sqm. 98.95. Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture. sqm. 88.60. Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture. sqm. 84.75. With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood). sqm. 34.95. With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood. sqm. 35.20. With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works. sqm. 29.10. With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat). sqm. 15.60. New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). Applying priming coat: 13.50.1 13.50.2 13.50.3. 13.50.4. 13.51. sqm. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1. 13.50. 150.65. Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 13.47.1. 13.48. sqm. New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1. 13.47. Rate. Finishing walls with textured exterior paint of required shade : 13.45.1. 13.46. Unit. Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : 13.51.1. One coat. sqm. 56.65. 13.51.2. Two coats. sqm. 90.05. SUB HEAD : 13.0 FINISHING. 231.
(22) Code No. 13.52. 13.53. Description. 13.52.1. On steel work. sqm. 122.50. 13.52.2. On concrete work. sqm. 124.50. sqm. 84.00. With a solution of 38 gms of copper acetate in a litre of soft water. sqm. 29.25. With a solution made of 13 gms of hydrochloric acid in a solution of 13 gms each of copper chloride, copper nitrate and ammonium chloride dissolved in a litre of soft water. sqm. 29.05. Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :. 13.54.2. 13.56. 13.57. Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture, over and including a priming of ready mixed zinc chromate yellow primer on new work: 13.55.1. 100 mm diameter pipes. metre. 35.85. 13.55.2. 150 mm diameter pipes. metre. 53.50. Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 13.56.1. 100 mm diameter pipes. metre. 40.55. 13.56.2. 150 mm diameter pipes. metre. 60.40. sqm. 32.20. Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.. sqm. 232.55. Coal tarring two coats on new work using 0.16 Litre and 0.12 litre coal tar per sqm in the first coat and second coat respectively.. sqm. 33.45. sqm. 84.45. sqm. 78.40. Painting with oil type wood preservative of approved brand and manufacture : 13.57.1. 13.58. 13.59 13.60. New work (two or more coats). Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 13.60.1. 13.61. New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. Applying a coat of mordant solution on G.S. sheet: 13.54.1. 13.55. Rate. Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.. 13.53.1 13.54. Unit. Two or more coats on new work. Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 13.61.1. Two or more coats on new work. SUB HEAD : 13.0 FINISHING. 232.
(23) Code No. 13.62. Description. 13.67.2. 13.71 13.72. sqm. 65.20. sqm. 76.50. Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish. sqm. 114.85. Two or more coats glue sizing with spar varnish or an under coat of flatting varnish. sqm. 115.85. sqm. 209.75. sqm. 92.70. sqm. 43.50. per letter per cm height. 2.70. Two or more coats on new work. Two or more coats on new work. Two or more coats on new works including a coat of wood filler. Polishing on wood work with ready mixed wax polish of approved brand and manufacture : 13.69.1. 13.70. 85.85. French spirit polishing : 13.68.1. 13.69. sqm. Two or more coats on new work. Varnishing with varnish of approved brand and manufacture : 13.67.1. 13.68. 68.35. Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade : 13.66.1. 13.67. sqm. Two or more coats on new work. Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 13.65.1. 13.66. 112.30. Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade : 13.64.1. 13.65. sqm. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. Painting with aluminium paint of approved brand and manufacture to give an even shade . 13.63.1. 13.64. Rate. Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.62.1. 13.63. Unit. New work. Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture. Lettering with black Japan paint of approved brand and manufacture Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in- charge (payment for providing grooves shall be made separately).. SUB HEAD : 13.0 FINISHING. 233. sqm. 582.60.
(24) Code No. 13.73. 13.74 13.75 13.76. 13.77 13.78. 13.79. 13.80. 13.81. 13.82. Description. Unit. Rate. Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 13.73.1. 15 mm wide and 15 mm deep groove. metre. 34.40. 13.73.2. 20 mm wide and 15 mm deep groove. metre. 34.95. Extra for washed grit plaster on exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.. sqm. 85.90. Extra for washed stone grit plaster on circular work not exceeding 6 m in radius (in two coats).. sqm. 60.45. Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-inCharge.. metre. 71.60. Extra for using white cement in place of ordinary cement in the top layer of the item of washed stone grit plaster.. sqm. 63.90. Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.. sqm. 217.35. Extra for addition of synthetic Polyester triangular fibre of length 6 mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement plaster/mortar by using 125 gms. of synthetic Polyester triangular fibre for 50 Kgs. cement used in cement mortar as per directions of Engineer-in-Charge.. Per Bag of 50 Kg of cement. 58.10. Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.. sqm. 87.35. Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 13.81.1. One coat. sqm. 30.90. 13.81.2. Two coats. sqm. 49.65. Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 13.82.1. One coat. sqm. 49.35. 13.82.2. Two coats. Sqm. 73.90. SUB HEAD : 13.0 FINISHING. 234.
(25) Code No. 13.83. 13.84. 13.85. Description. Rate. Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 13.83.1. One coat. sqm. 46.65. 13.83.2. Two coats. Sqm. 71.00. Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 13.84.1. One coat. sqm. 49.75. 13.84.2. Two coats. sqm. 75.00. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre. sqm. 38.45. With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ litre. sqm. 32.55. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. sqm. 36.95. 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In-Charge.. sqm. 146.45. Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 13.85.1. 13.85.2. 13.85.3 13.86. Unit. SUB HEAD : 13.0 FINISHING. 235.
(26) SUB HEAD : 14.0. REPAIRS TO BUILDING. 236.
(27) BASIC RATES (SH: 14.0 REPAIRS TO BUILDING) Code No.. Description. Unit. Rate. 0006 0011 0058 0085 0086. Hire charges of Spraying machine including electric charges Hire charges of Pump set of capacity 4000 litres/hour Air compressor Using cost of Ultra Violet Radiation tube Compressor, gun, rubber pipes & other accessories- hire charge of plant & machinery i/c necessary fuel Hire Charges of Suction Jeting machine 2200 PSI machine including POL and operator Bandhani Bhisti Blacksmith 1st class Blacksmith 2nd class Carpenter 1st class Carpenter 2nd class Beldar Coolie Fitter (grade 1) Assistant fitter or 2nd class fitter Glazier Mason (brick layer) 1st class Mason (brick layer) 2nd class Mason 1st class Mate Sewer man Mistry Painter Sprayer (for bitumen, tar etc.) Skilled Beldar (for floor rubbing etc.) White Washer Mason (average) Carpenter (average) Technician Stone Aggregate (Single size) : 20 mm nominal size Stone Aggregate (Single size) : 10 mm nominal size Safeda ballies 125 mm diameter Bhusa Portland Cement (OPC-43 grade) Brass single acting spring hinges 150 mm Brass single acting spring hinges 125 mm Brass single acting spring hinges 100 mm Brass double acting spring hinges 150 mm. day day hour Hour. 250.00 650.00 200.00 189.00. day. 4000.00. day day day day day day day day day day day day day day day day day day day day day day day day day cum cum metre quintal tonne each each each each. 36000.00 407.00 407.00 487.00 448.00 487.00 448.00 368.00 368.00 487.00 448.00 448.00 487.00 448.00 487.00 407.00 390.00 487.00 448.00 407.00 407.00 407.00 467.00 467.00 775.00 1300.00 1300.00 35.00 600.00 5700.00 460.00 298.00 260.00 498.00. 0087 0100 0101 0102 0103 0111 0112 0114 0115 0116 0117 0119 0123 0124 0126 0128 0129 0130 0131 0138 0139 0141 0155 0156 0160 0295 0297 0302 0308 0367 0389 0390 0391 0392. SUB HEAD : 14.0 REPAIRS TO BUILDING. 237.
(28) Code No.. Description. Unit. Rate. 0393. Brass double acting spring hinges 125 mm. each. 410.00. 0394. Brass double acting spring hinges 100 mm. each. 370.00. 0404. Brass flush bolt 250 mm. each. 150.00. 0405. Brass flush bolt 150 mm. each. 130.00. 0406. Brass flush bolt 100 mm. each. 90.00. 0417. Brass 150 mm floor door stopper (0.357kg). each. 170.00. 0418. Brass hard drawn hooks and eyes 300 mm. 10 Nos. 650.00. 0419. Brass hard drawn hooks and eyes 250 mm. 10 Nos. 635.00. 0420. Brass hard drawn hooks and eyes 200 mm. 10 Nos. 590.00. 0421. Brass hard drawn hooks and eyes 150 mm. 10 Nos. 450.00. 0422. Brass hard drawn hooks and eyes 100 mm. 10 Nos. 400.00. 0423. Brass casement window fastener. each. 50.00. 0427. Brass quadrant stays 300 mm. each. 125.00. 0428. Brass fanlight catch. 10 Nos. 200.00. 0429. Brass fanlight pivot. 10 Nos. 195.00. 0430. Brass chain with hook for fan light catch. each. 40.00. 0442. Brass helical spring 150 mm. each. 310.00. 0444. Brass curtain rod 20 mm dia 1.25 mm thick. metre. 120.00. 0445. Brass curtain rod 25 mm dia 1.25 mm thick. metre. 140.00. 0446. Brass brackets (curtain rods) 20 mm. each. 45.00. 0449. Brass screws 50 mm. 100 Nos. 220.00. 0450. Brass screws 40 mm. 100 Nos. 170.00. 0452. Brass screws 25 mm. 100 Nos. 100.00. 0524. Chromium plated Brass butt hinges (heavy) type 75x65x4 mm weighing not less than 200gms. 10 Nos. 1000.00. 0525. Chromium plated Brass butt hinges (light/ordinary) type 125x70x4mm. 10 Nos. 900.00. 0526. Chromium plated Brass butt hinges (light/ordinary) type 100x 70x4 mm. 10 Nos. 750.00. Chromium plated Brass butt hinges (light/ordinary) type 75x 40x2.5 mm. 10 Nos. 460.00. Chromium plated Brass butt hinges (light/ordinary) type 50x 40x2.5 mm. 10 Nos. 200.00. 0585. Chromium plated Brass screws 50 mm. 100 Nos. 340.00. 0586. Chromium plated Brass screws 40 mm. 100 Nos. 310.00. 0587. Chromium plated Brass screws 30 mm. 100 Nos. 250.00. 0589. Chromium plated Brass screws 20 mm. 100 Nos. 170.00. 0595. Bright finished or black enameled mild steel butt hinges 100x 58x1.90 mm. 10 Nos. 85.00. Bright finished or black enameled mild steel butt hinges 50x 37x1.50 mm. 10 Nos. 50.00. 0527 0528. 0597. SUB HEAD : 14.0 REPAIRS TO BUILDING. 238.
(29) Code No. 0608. Description Nickel plated bright finished mild steel piano hinges 1 mm thick 25 mm wide. Unit. Rate. metre. 40.00. 0637. Bright finished or black enameled mild steel screws 40 mm. 100 Nos. 63.00. 0639. Bright finished or black enameled mild steel screws 25 mm. 100 Nos. 37.00. 0640. Bright finished or black enameled mild steel screws 20 mm. 100 Nos. 32.00. 0761. Fuel wood. quintal. 500.00. 0771. Kerosene oil. litre. 45.00. 0772. White cement based polymer modified self curing compound in powder form. 0775. Dehradun white lime. 0811. Mud (dry). 0815. kg. 15.00. quintal. 550.00. cum. 150.00. Dry distemper. kilogram. 30.00. 0816. Oil bound washable distemper/ Acrylic distemper. kilogram. 45.00. 0826. Aluminium paint. litre. 130.00. 0827. Acid proof paint (chocolate or black). litre. 225.00. 0828. Anticorrosive bituminous paint (black). litre. 100.00. 0829. Black Japan paint. litre. 90.00. 0833. Synthetic enamel paint in black or chocolate shade. litre. 170.00. 0835. Plastic emulsion paint. litre. 200.00. 0845. Roofing paint for iron sheets in red colour. litre. 120.00. 0851. Water proofing cement paint. kilogram. 38.00. 0855. Wax polish (ready made). kilogram. 250.00. 0856. Ordinary varnish. litre. 90.00. 0857. Superior copal varnish. litre. 130.00. 0858. Superior spar varnish. litre. 130.00. 0859. Oil type wood preservative. litre. 140.00. 0863. Putty for wood work. kilogram. 30.00. 0982. Coarse sand (zone III). 0999. Shellac. 1000. Spirit. 1003. Mild steel round bar above 12 mm dia. quintal. 3575.00. 1007. Structural steel such as tees, angles channels and R.S. joists. quintal. 3775.00. 1008. Flats up to 10 mm in thickness. quintal. 3675.00. 1023. Galvanised steel J or L hooks 8 mm dia. 10 Nos. 115.00. 1034. Bolts and nuts up to 300 mm in length. quintal. 5100.00. 1174. Red sand stone slab 45 mm to 50 mm thick (un-dressed). sqm. 225.00. 1186. Superior class teak wood such as Dandeli, Balarshah or Malabar in planks. 10 cudm. 1100.00. 1188. First class teak wood in planks. 10 cudm. 850.00. 1189. Second class teak wood in scantling. 10 cudm. 660.00. 1190. Second class teak wood in planks. 10 cudm. 675.00. SUB HEAD : 14.0 REPAIRS TO BUILDING. 239. cum. 1200.00. kilogram. 300.00. litre. 50.00.
(30) Code No.. Description. Unit. Rate. 1194. Second class deodar wood in planks. 10 cudm. 500.00. 1196. First class kail wood in planks. 10 cudm. 310.00. 1199. Sal wood in scantling. 10 cudm. 600.00. 1208. Bitumen washer. 100 Nos. 30.00. 1209. G.I. plain washer thick. 100 Nos. 35.00. 1213. Water proofing materials. kilogram. 35.00. 1215. Welding by electric plant. cm. 2.00. 1301. Bleaching powder. 1314. C.P.brass chain with 32 mm dia rubber plug. each. 40.00. each. 40.00. kg. 22.00. quintal. 1750.00. 1315. C.P.brass chain with 40 mm dia rubber plug. 1880. Dismenteled P or S trap scrap (approx wt 2kg). 1890. Centrifugally SCI(spun) S & S P or S trap. each. 300.00. 1953. Vitreous china Indian type W.C. pan of size 580 mm. each. 450.00. 1954. Vitreous china orrisa type W.C. pan of size 580 mm. each. 780.00. 1970. Vitreous china foot rests 250x125x25 mm. pair. 100.00. 2201. Carriage of Bricks. 1000 Nos. 276.72. 2202. Carriage of Stone aggregate below 40 mm nominal size. cum. 103.77. 2203. Carriage of Coarse sand. cum. 103.77. 2204. Carriage of Timber. cum. 118.59. 2205. Carriage of Steel. tonne. 92.24. 2209. Carriage of Cement. tonne. 92.24. 2216. Carriage of Stone blocks white & red sand stone & kota stone slab. tonne. 92.24. 2264. Carriage of Rubbish. cum. 103.77. 2406. Float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm). sqm. 286.00. Float glass sheet of nominal thickness 5.5 mm (weight not less than 13.50 kg/sqm). sqm. 490.00. 10 cudm. 340.00. each. 165.00. Common burnt clay F.P.S. (non modular) bricks class designation 7.5. 1000 Nos. 4500.00. 4009. Mild steel tubes hot finished welded type. kilogram. 42.00. 4202. Red oxide Zinc chromate primer. litre. 65.00. 7019. Dash fastener / Chemical fastener. each. 15.00. 7241. Melamine polish. litre. 290.00. 7346. Double coupler. each. 48.00. 7387. Spigot for standard jointing. kilogram. 45.00. 7397. Base Jack. each. 150.00. 7398. Challies. each. 800.00. 7399. Cup locks. each. 50.00. 7442. Wheel 75 mm dia. 40 mm wide. each. 65.00. 2407 2466. Hollock wood in scantling. 2467. Chromium plated Brass pull bolt lock (locking bolt) of size 85 mm x 42 mm with screws, bolts, nuts and washers complete. 2602. SUB HEAD : 14.0 REPAIRS TO BUILDING. 240.
(31) Code No.. Description. Unit. 7752. PVC slotted pipe 200 mm dia as per IS: 12818. 8500. Water for jetting / blowback. 8505. Rate. metre. 700.00. 1000 litre. 1500.00. Acrylic exterior paint. litre. 170.00. 8506. Premium Acrylic exterior paint. litre. 203.00. 8507. Textured exterior paint. litre. 230.00. 8508. Primer for cement paint. litre. 70.00. 9977. Carriage. L.S.. 1.73. 9988. Carriage and sundries. L.S.. 1.73. 9999. Sundries. L.S.. 1.73. SUB HEAD : 14.0 REPAIRS TO BUILDING. 241.
(32) 14.0 REPAIRS TO BUILDING Code No. 14.1. 14.2. 14.3. 14.4. Description. 14.6. 14.7. 14.8. Rate. Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. 14.1.1. With cement mortar 1:4 (1 cement : 4 fine sand). sqm. 264.80. 14.1.2. With cement mortar 1:4 (1cement: 4 coarse sand). sqm. 274.80. Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. 14.2.1. Door chowkhats. each. 852.70. 14.2.2. Window chowkhats. each. 529.50. 14.2.3. Clerestory window chowkhats. each. 387.10. each. 157.95. sqm. 546.25. Fixing chowkhat in existing opening in brick/ RCC wall with dash fasteners/ Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener. Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per directions of Engineer-In-Charge. 14.4.1. 14.5. Unit. For door/ window/ clerestory window. Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: 14.5.1. Float glass panes of thickness 4 mm. sqm. 637.90. 14.5.2. Float glass panes of thickness 5.5 mm. sqm. 898.55. Renewing glass panes, with wooden fillets wherever necessary: 14.6.1. Float glass panes of thickness 4 mm. sqm. 852.60. 14.6.2. Float glass panes of thickness 5.5 mm. sqm. 1113.25. Renewing glass panes and refixing existing wooden fillets: 14.7.1. Float glass panes of thickness 4 mm. sqm. 688.65. 14.7.2. Float glass panes of thickness 5.5 mm. sqm. 949.30. Supplying and fixing new wooden fillets wherever necessary: 14.8.1. 2nd class teak wood fillets. metre. 38.65. 14.8.2. Hollock wood fillets. metre. 34.20. SUB HEAD : 14.0 REPAIRS TO BUILDING. 242.
(33) Code No.. Description. Unit. Rate. 14.9. Renewal of old putty of glass panes (length). metre. 25.45. 14.10. Refixing old glass panes with putty and nails. sqm. 330.75. 14.11. Fixing old glass panes with wooden fillets (excluding cost of fillets). sqm. 295.05. 14.12. Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete.. each. 259.50. Regrading terracing of mud phaska covered with tiles or brick, in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per directions of Engineer-In-Charge.. sqm. 314.10. sqm. 659.10. cum. 76828.35. 14.13. 14.14. Replacing sand stone slabs in roofing, laid in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary repairs and cement pointing with same mortar complete, including disposal of rubbish to dumping ground, all complete as per directions of Engineer-In-Charge. 14.14.1. 14.15. Renewing wooden battens in roofs, including making good the holes in wall and painting with oil type wood preservative of approved brand and manufacture complete, including removal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. 14.15.1. 14.16. 14.16.2. 14.18. Sal wood battens. Renewing wooden beams in roofs including making good the holes in walls and painting with oil type wood preservative of approved brand and manufacture complete, including removal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. 14.16.1. 14.17. Red/ white sand stone slabs 30 to 50 mm thick. Not exceeding 4.00 metres in length. 14.16.1.1. Sal wood beams. cum. 79341.25. 14.16.1.2. Hollock wood beams. cum. 48223.75. Above 4.00 metres and upto 5.00 metres length. 14.16.2.1. Sal wood beams. cum. 80485.90. 14.16.2.2. Hollock wood beams. cum. 49336.15. Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge.. sqm. 29.65. Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska : 14.18.1. With F.P.S. brick tiles. sqm. 62.95. 14.18.2. With modular brick tiles. sqm. 64.00. SUB HEAD : 14.0 REPAIRS TO BUILDING. 243.
(34) Code No. 14.19. 14.20. 14.21. 14.22. Description. Unit. Rate. Taking out wind ties from roof including cutting out rusted bolts, nuts etc. and removing materials to any distance within compound and stacking.. kg. 2.25. Fixing of old wind tie with new fittings including painting two or more coats with anticorrosive bitumastic paint of approved brand & manufacturer over and including priming coat of ready mixed zinc chromate yellow primer of approved brand.. metre. 74.40. Renewing bottom rail and/or top runner of collapsible gate including making good all damages and applying priming coat of zinc chromate yellow primer of approved brand and manufacturer.. kg. 144.10. Renewing Wrought iron or M.S. Wheel or roller of steel door or gate and fitting and fixing the same with necessary clamps, nuts and bolts/welding and erection etc. complete. 14.22.1. Wheel 50 mm dia and below. per wheel. 122.65. 14.22.2. Wheel above 50 mm dia. per wheel. 187.25. kilo litre. 104.30. cum. 533.20. cum. 3972.20. Superior class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.. sqm. 3492.55. Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.. sqm. 2954.85. Superior class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.. sqm. 3563.10. Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.. sqm. 2985.05. sqm. 2837.20. EARTH WORK 14.23 14.24. Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. Mud mortar made with local clay good earth. BRICK WORK. 14.25. Brick work with common burnt clay bricks of class designation 7.5 in mud mortar WOOD WORK. 14.26. Providing and fixing 25 mm thick shutters for cup board etc. : 14.26.1. Panelled or panelled & glazed shutters : 14.26.1.1. 14.26.1.2. 14.26.2. Glazed shutters : 14.26.2.1. 14.26.2.2. 14.27. Providing and fixing plain jaffri door and window shutters including bright or/and black enamelled M.S. butt hinges with necessary screws 35x10 mm laths placed 35 mm apart (frames to be paid separately), including fixing 50x12 mm beading complete with : 14.27.1. Second class teak wood. SUB HEAD : 14.0 REPAIRS TO BUILDING. 244.
(35) Code No. 14.28. 14.29. 14.30. 14.31. 14.32. 14.33. 14.34. 14.35. 14.36. Description. Unit. Rate. Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 14.28.1. 20 mm diameter.. metre. 222.10. 14.28.2. 25 mm diameter.. metre. 245.35. kg. 61.80. Providing and fixing M.S. round or square bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows. Providing joists (karries) including hoisting, fixing in position and applying wood preservative on unexposed surface etc. complete with : 14.30.1. Sal wood. cum. 75873.50. 14.30.2. Hollock wood. cum. 45070.55. Providing and fixing bright finished brass single acting spring hinges with necessary brass screws etc. complete : 14.31.1. 150 mm. each. 586.65. 14.31.2. 125 mm. each. 398.45. 14.31.3. 100 mm. each. 349.70. Providing and fixing bright finished brass double acting spring hinges with necessary brass screws etc. complete : 14.32.1. 150 mm. each. 630.75. 14.32.2. 125 mm. each. 528.55. 14.32.3. 100 mm. each. 477.45. Providing and fixing bright finished brass flush bolts with necessary brass screws etc. complete : 14.33.1. 250 mm. each. 193.25. 14.33.2. 150 mm. each. 168.10. 14.33.3. 100 mm. each. 121.65. each. 211.15. Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete Providing and fixing bright finished brass hard drawn hooks and eyes : 14.35.1. 300 mm. each. 79.05. 14.35.2. 250 mm. each. 77.35. 14.35.3. 200 mm. each. 72.10. 14.35.4. 150 mm. each. 55.85. 14.35.5. 100 mm. each. 50.05. each. 35.25. Providing and fixing bright finished brass fan light pivot with necessary brass screws etc. complete.. SUB HEAD : 14.0 REPAIRS TO BUILDING. 245.
(36) Code No. 14.37 14.38 14.39 14.40. 14.41. Description. Unit. Rate. Providing and fixing 300 mm long bright finished brass chain with hook for fan light including necessary brass screws etc. complete.. each. 56.95. Providing and fixing bright finished brass quadrant stay 300 mm long with necessary brass screws etc. complete.. each. 155.65. Providing and fixing bright finished brass helical door spring (superior quality).. each. 404.55. Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete. 14.40.1. 125x70x4 mm (ordinary type). each. 156.95. 14.40.2. 100x70x4 mm (ordinary type). each. 128.85. 14.40.3. 75x65x4 mm (heavy type). each. 146.15. 14.40.4. 75x40x2.5 mm (ordinary type). each. 83.40. 14.40.5. 50x40x2.5 mm (ordinary type). each. 35.85. each. 205.95. Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete. FINISHING. 14.42. 14.43. 14.44. 14.45. White washing with lime to give an even shade : 14.42.1. Old work (two or more coats). sqm. 10.25. 14.42.2. Old work (one or more coats). sqm. 6.30. Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. sqm. 8.35. Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade.. sqm. 30.05. sqm. 33.35. sqm. 10.80. sqm. 43.60. metre. 26.85. metre. 13.00. Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 14.45.1. 14.46. 14.47. Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 14.47.1. 14.48. Old work (one or more coats). Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture over and including a priming coat of ready mixed zinc chromate yellow primer on new work : 14.48.1. 14.49. Old work (one or more coats). 75 mm diameter pipes. Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture on old work : 14.49.1. 75 mm diameter pipes. SUB HEAD : 14.0 REPAIRS TO BUILDING. 246.
(37) Code No.. 14.50. 14.51. 14.52. Description 100 mm diameter pipes. metre. 17.15. 14.49.3. 150 mm diameter pipes. metre. 24.60. Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with aluminium paint of approved brand and manufacture over a priming coat of ready mixed zinc chromate yellow primer on new work : 14.50.1. 75 mm diameter pipes. metre. 27.60. 14.50.2. 100 mm diameter pipes. metre. 38.75. 14.50.3. 150 mm diameter pipes. metre. 57.75. Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour on old work : 14.51.1. 75 mm diameter pipes. metre. 13.55. 14.51.2. 100 mm diameter pipes. metre. 17.45. 14.51.3. 150 mm diameter pipes. metre. 25.00. sqm. 24.80. sqm. 55.25. sqm. 51.30. sqm. 44.40. sqm. 55.75. sqm. 43.55. sqm. 105.85. sqm. 46.95. Per letter per cm height. 1.70. Painting with oil type wood preservative of approved brand and manufacture:. One or more coats on old work. Polishing on wood work with ready made wax polish of approved brand and manufacture : 14.59.1. 14.60. One or more coats on old work. French spirit polishing : 14.58.1. 14.59. One or more coats on old work. Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 14.57.1. 14.58. One or more coats on old work. Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade : 14.56.1. 14.57. One or more coats on old work. Painting with aluminium paint of approved brand and manufacture to give an even shade: 14.55.1. 14.56. One or more coats on old work. Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 14.54.1. 14.55. Old work (one or more coats). Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: 14.53.1. 14.54. Rate. 14.49.2. 14.52.1 14.53. Unit. Old work. Re-lettering with black Japan paint of approved brand and manufacture.. SUB HEAD : 14.0 REPAIRS TO BUILDING. 247.
(38) Code No. 14.61 14.62. 14.63. Description Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.. each. 62.65. 14.62.2. 40 mm dia. each. 62.65. sqm. 29.80. Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.. sqm. 55.70. Old work (one or more coats @ 2.20 kg/10 sqm) complete.. sqm. 37.90. Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm.. sqm. 124.75. Old work (One or more coats) applied @ 1.82 ltr/10 sqm.. sqm. 76.20. Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface. sqm. 68.95. Old work (One or more coat applied @ 0.90 ltr/10 sqm).. sqm. 45.35. Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface. sqm. 70.75. Old work (one or more coats applied @ 0.83 ltr/10 sqm).. sqm. 47.25. Distempering with 1st quality acrylic washable distemper (ready made) of approved manufacturer and of required shade and colour complete. as per manufacturer's specification.. Finishing walls with textured exterior paint of required shade :. 14.65.2. Finishing walls with Acrylic Smooth exterior paint of required shade: 14.66.1 14.66.2. Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade 14.67.1. 14.67.2 14.69. One or more coats on old work. Finishing walls with water proofing cement paint of required shade :. 14.65.1. 14.67. 44.80. 32 mm dia. 14.64.2. 14.66. sqm. 14.62.1. 14.64.1. 14.65. Rate. Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin:. 14.63.1 14.64. Unit. Varnishing with varnish of approved brand and manufacture: 14.69.1. One or more coats with copal varnish. sqm. 46.95. 14.69.2. One or more coats with spar varnish. sqm. 47.50. 14.70. Melamine polishing on wood work (one or more coat).. sqm. 79.50. 14.71. Varnishing with flatting varnish of approved brand and manufacture one or more coats on old work.. sqm. 47.20. 14.72. Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The. SUB HEAD : 14.0 REPAIRS TO BUILDING. 248.
(39) Code No.. Description. Unit. Rate. sqm. 160.15. Providing and fixing bright finished brass casement window fasteners or peg stays to windows/ ventilators with necessary welding and machine screws etc. complete.. kg. 420.20. Providing and fixing 14 mm bright finished brass spring catch to steel centre hung ventilators with necessary welding and machine screws etc. complete.. each. 49.20. Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In- Charge.. sqm. 368.90. Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account). litre. 0.20. Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge.. each. 47.55. Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm dia for all depth.. metre. 217.80. scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. 14.73. 14.74. 14.75. ROUTINE MAINTENANCE WORK 14.75A. 14.76. 14.77. SUB HEAD : 14.0 REPAIRS TO BUILDING. 249.
(40) Code No. 14.78. Description. Unit. Rate. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.. sqm. 40.70. Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in- charge.. each. 182.45. Cleaning of under ground sump, Over Head R.C.C. Tank ( independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:(i). Tank shall be emptied of water by pumping & bottom shall be cleaned of slit and other deposits.. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.. 14.79. 14.80. 14.81. 14.82. 14.83 14.84. 14.85. Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. 14.80.1. Long pattern W.C Pan of size 580x440 mm. each. 1892.80. 14.80.2. Orissa pattern W.C Pan of size 580x440 mm. each. 2127.85. Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.. each. 138.40. Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.. each. 55.45. Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.. sqm. 1.50. Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes within 50 metres lead as per direction of Engineer- in-Charge. (a) Internal Work - Exposed on wall. metre. 2.00. Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.. each. 176.40. SUB HEAD : 14.0 REPAIRS TO BUILDING. 250.
(41) SUB HEAD : 15.0. DISMANTLING AND DEMOLISHING. 251.
(42) BASIC RATES (SH:15.0 DISMANTLING AND DEMOLISHING) Code No.. Description. Unit. Rate. 0038. Tractor with ripper attachment. day. 1100.00. 0039. Tractor with trolley. day. 1250.00. 0040. Air compressor 250 cfm with two leads for pneumatic cutters / hammers. day. 1500.00. 0041. Joint cutting machine with 2-3 blades. day. 750.00. 0100. Bandhani. day. 407.00. 0101. Bhisti. day. 407.00. 0103. Blacksmith 2nd class. day. 448.00. 0112. Carpenter 2nd class. day. 448.00. 0114. Beldar. day. 368.00. 0115. Coolie. day. 368.00. 0116. Fitter (grade 1). day. 487.00. 0117. Assistant Fitter or 2nd class Fitter. day. 448.00. 0123. Mason (brick layer) 1st class. day. 487.00. 0124. Mason (brick layer) 2nd class. day. 448.00. 0128. Mate. day. 407.00. 0130. Mistry. day. 487.00. 0139. Skilled Beldar (for floor rubbing etc.). day. 407.00. 0761. Fuel wood. quintal. 500.00. 0771. Kerosene oil. litre. 45.00. 2264. Carriage of Rubbish. cum. 103.77. 9977. Carriage. L.S.. 1.73. 9988. Carriage and sundries. L.S.. 1.73. 9999. Sundries. L.S.. 1.73. SUB HEAD : 15.0 DISMANTLING AND DEMOLISHING. 252.
